INTRODUCTION
Temperature Indicators / Controllers play an important part in any process industry. Quick and accurate measurement / control of a process temperature will improve the final product quality, reliability and reduce rejection. Temperature indication and control is therefore one of the prime considerations in any process industry.
The Sleek 92 series is microcontroller based programmable temperature indicator/controller designed for fast and accurate measurement / control. The instrument is designed using highly reliable electronic components. The process temperature is displayed in digits, which gives better resolution compared to analog indicator. The ESD 921 single set point series accepts all types of Pt - 100, Thermocouples, 0 - 20 mA as well as 4 - 20 mA as input.
The instrument is immune to mechanical vibrations. Even the mounting position will not affect the measurement accuracy. The large bright red LED seven segment display allows long distance readability. Use of highly reliable electronic components with lowest temperature coefficient ensure long and trouble free service. The instrument is tested for its performance under various climatic conditions. Wide ranges of measurements are available depending on the sensor used.
APPLICATION
The Sleek 92 series
temperature controllers can be used in almost any industry, laboratory etc. where accurate temperature control is needed to be carried out.
FEATURES
- Proven troublefree field performance
- Highly compact
- Dust and vermin proof enclosure with epoxy
- powder coating
- LED display gives better readability at long range
- Fast response time
- Highly accurate
- Available in different DIN std. cutouts
- Designed for Pt-100, Thermocouples and
- 4 - 20 mA input
- Fail safe relay logic
- Maximum MTBF and minimum MTTR
- Feather touch push button
- Wide supply variation and environmental band
- Minimum overshoot undershoot
- User friendly programming
SPECIFICATIONS
- Model Sleek :
a)Sleek 921X
b)Sleek 9220
c)Sleek 9223
d)Sleek 9243
- Ranges : Std. as per chart below (other on demand)
- Input : Pt - 100 / Thermocouple / 4 - 20 mA
- Indication : 399.9 12.5 mm Red LED display
- Indication acuracy : +/- 0.2 % of fullscale +/- 1 digit
- Least count : 0.1 C upto 400 C, 1 C above 400 C
- Power supply : 230 V AC, +/- 10 % , 50 Hz with Earth
- Relative Humidity : 90 % Non Condensing
- Ambient Temperature : 0 to 55 C
- o Amb. Temp. compensation : Built in upto 55 C
- Accuracy deviation due to a) Temperature change : +/- 0.002 % / C, ref at 25 C
b) Supply Variation : +/- 0.005 % / V
- Sensor break indication : OPen
- Input impedance : < 10 Mohms, (only for T/C input )
- Recalibration (if reqd) : By Zero and Span pots inside
- Power consumption : 6 VA
- Setpoints
a)One
b)Two
c)Four
- Control action : Proportional
- Set point Adjust : Through Flat Membrane key pads
- On / Off differential : From 1 to 7 C (for LC = 1 C)
- From 0.1 to 2 C( for LC = 0.1 C)
- Duty Cycle : Self tuning
- Cycle Time (On/Off) : From 6 to 240 Sec
- Proportional Band : From +/- 0.2 to +/- 9.9 C around setpoint
- Relay Output : One set of potential free Relay contact changeover contact 5 Amp resistive at 230V AC
- Output (optional) : 4 - 20 mA for retransmission 24 V DC, 100mA field supply
- Relay logic : User selectable High or Low
- Relay ON indication : By Red LED
- Sensor break protection : Relay ‘Off’ (Relay ‘On’ on demand)
- Mounting : Flush mounting
- Enclosure : IP 55 mild steel with power coating
- Termination : PUT 2.5 mm /PBT
- Weight : 700 grams
ESD Address:
Electronics Systems & Devices,
ESD House, 55 Hadapsar Industrial Estate,
Pune 411013, Maharashtra, India.
Website:
https://esd-india.com
